DIY Tub Installation.
DIY Tub Installation.
Blog Article
Do you find yourself trying to locate know-how on Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't specifically brain surgery, yet it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is conveniently accessible, the project can move speedily; if you have to open up a wall surface to get rid of the old bathtub and place the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will need a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually certified on your own for the job and fit trying it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly assist you mount a brand-new tub in your restroom if you have already acquired a brand-new tub and don't require to alter the arrangement of your previous water pipelines.
Your devices and material checklist should make up the following:
Preparing for the Setup
First of all, the supporting framework supplied with the bath needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be quite problematic because of the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, put the tub in the needed position. The wooden boards are useful in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub up until the level checks out level.
To install faucets, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and check all joints and also brand-new pipework for leaks and tighten them if essential. Load the tub and additionally examine the overflow electrical outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized at least when as this will settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers are in location between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, triggering the water to pass through the wall between the bath and also the tiling, leading to issues with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader on Installing A Bathtub, I assumed sharing that excerpt was really helpful. I beg you take the time to share this blog post if you liked it. I cherish reading our article about Tools You Need to Install a New Bathtub .
This Page Report this page